nicilaskin — copper art
heart bracelet
Posted by 36877008 on
anticlastic bronze cuff with copper hearts cut a 1 1/4 or 1 1/2 inch wide strip from 20 gauge bronze cut lots and lots of hearts from copper I have a heart cutter from swanstrom , flux the back of your hearts and add solder I use hard wire solder for that heat the hearts until the solder melts and then flux the bronze strip and solder the hearts to it quench in water form your bracelet Now I realize that not everybody has a metal press with the anticlastic / synclastic former ,so you can make the bracelet normal...
-
Comment
- 0 comment
- Tags: art, bracelet tutorial, bracelets, copper art, copper bracelet, handmade jewelry, how to, how to make a bracelet, how to make jewelry, jewelry tutorials, metal art, metal smithing, metal tutorials, metal work, metalworking, nicilaskin, silver smith
easy teaxture if you do not have a rolling mill
Posted by 36877008 on
fun with metal easy texture for metal this is basic metal smithing 101 take a patterned steel sheet tape a strip of metal that is softer then the steel to the plate use clear tape so you can see the back . Start hammering with a ball peen hammer on the whole back ,basically covering the back with dimples .You will need some elbow grease with this as this takes some serious hammer time WATCH YOUR FINGERS !!! while you hammer the back the metal expands and gets pushed into the pattern in the steel plate thus creating a negative...
-
Comment
- 1 comment
- Tags: button tutorial, copper art, handmade jewelry, how to, how to make a bracelet, how to make jewelry, jewelry making, jewelry tutorials, metal, metal art, metal smithing, nicilaskin, silver smith, silver smithing, smithing, tutorial, tutorials, Uncategorized
three hearts
Posted by 36877008 on
three hearts 3 metal hearts :) I used copper ,brass , sterling silver cut 3 hearts in different sizes from different metals mine are copper, brass , sterling silver cut sterling silver wire to make your ring shank silver wire ,or metal wire is the best you can use for ring shanks , the width is always consistent and its a lot less work mark with your makers stamp and 925 for the sterling bend your ring shank until the ends meet flux and add solder - heat with a torch until the solder flows The solder will flow when...
-
Comment
- 0 comment
- Tags: art, bracelet tutorial, copper art, handmade jewelry, how to make a bracelet, how to make jewelry, jewelry making, jewelry tutorials, nature, nicilaskin, rings, silver smith, silver smithing, smithing, tutorials
copper tea light holder
Posted by 36877008 on
made a copper tea light holder :) cut a 1 1/2 inch wide strip by 6 inch long from copper draw your shapes onto the metal small tip (if you like a shape make a template out of plastic via exacto knife ) cut out your lizards i use a jewelers saw with 1/0 blades shape the strip ,dome a circle and cut a 3x3 inch square solder everything together ( use plumbers solder as it has a low melting temp ) start polishing - steel wool will do or sand paper put a tea light in and light it...
-
Comment
- 0 comment
- Tags: art, bracelet tutorial, copper art, copper bracelet, cute, handmade jewelry, how to make a bracelet, how to make jewelry, jewelry making, jewelry tutorials, lizard, metal work, nicilaskin, silver smithing, smithing, tea light, tea light holder, Uncategorized
copper buttons
Posted by 36877008 on
copper buttons made some buttons for my mom I remember as a child my mom had a small wooden box with tons of buttons in it . I was very facinated by it and when she got that box out to make something I would sit on the floor and play for hours . She still has that box with the buttons , so I made her a couple of new ones out of copper I cut out 2 discs an 2 flowers from copper I used a disc cutter for the circles as sawing a circle by hand and...
-
Comment
- 0 comment
- Tags: art, button, button tutorial, copper, copper art, copper buttons, handmade, handmade jewelry, how to make jewelry, jewelry making, metal smithing, metal work, silver smith, Uncategorized